November 8, 2026
Sump Pump Repair: Signs, Fixes, Costs and When to Call

A sump pump that won’t start, won’t stop or only hums needs a licensed plumber, and fast, because these pumps tend to fail during the storms that put the most load on them. Most repairs are small: a stuck float switch, a failed check valve, a tripped circuit or a clogged intake. A dead motor usually means replacing the whole pump. Below you’ll find what usually goes wrong, what you can safely look at before the plumber arrives, what repair typically costs and how to keep the pump from failing again.
TL;DR
- The most common mechanical failure is a float switch stuck ON or OFF, so the pump runs nonstop or never starts.
- Safe checks are limited: confirm power, look at the outlet and breaker, and lift the float with a broom handle. Anything electrical, or any standing water near a panel, is a job for a licensed pro.
- National averages put a sump pump repair near $475, and component fixes cost less than replacement.
- A sealed submersible motor can’t be rebuilt at home. If the motor is gone, the pump is replaced.
- Test the pump twice a year and before hurricane season. Plan on replacing it around the 10-year mark.
Table of Contents
- Signs your sump pump needs repair
- What usually goes wrong
- What you can safely check first
- When to call a plumber
- What a sump pump repair visit covers
- Repair or replace?
- What sump pump repair costs
- How to keep your sump pump from failing
- Need a plumber for your sump pump?
- FAQ
- Sources
Signs your sump pump needs repair
A sump pump is a quiet machine until it isn’t. These are the symptoms that point to a problem:
- It doesn’t turn on when the pit is full.
- It runs constantly, even when the pit is nearly empty.
- It hums but doesn’t move water.
- It cycles on and off every few seconds.
- It’s much louder than it used to be, or it vibrates.
- It drains slowly, so the pit stays high for a long time after rain.
- The breaker trips when the pump starts.
Southern Living advises calling a plumber when a pump doesn’t turn on, drains slowly, doesn’t switch on or off when it should, cycles repeatedly or gets really noisy. The plumber can check the switch, the check valve and the drainage pipe.
In the Tampa Bay area, many homes don’t have a traditional basement. A sump pump here is more often found in a crawl space, a low garage, a lower-level addition or a commercial property with below-grade space. The failure modes are the same, but the rainy season and hurricane storm surge make the stakes higher.
What usually goes wrong
The Institute for Catastrophic Loss Reduction groups most sump system failures into three categories: the float or switch, the pump itself and the electric power supply. Here is how each one shows up.
Stuck or failed float switch
The City of Ann Arbor’s guide to sump pump failure points says the most common mechanical failure is a switch stuck in the ON or OFF position. Stuck ON, the pump runs continuously. Stuck OFF, it never starts and the pit overflows. A float can also get snagged on the pit wall or the discharge pipe, which gives the same result.
A float with a hole in it fills with water and can’t rise to trigger the motor. The ICLR booklet says in that case the float or the whole pump should be replaced right away.
Failed check valve
The check valve keeps pumped water from flowing back down the discharge pipe into the pit. When it fails, water returns to the pit, each cycle removes less water and the pump starts more often. The same city guide notes that this extra cycling can make the pump fail early. If you hear a gurgle or a thump after the pump shuts off, or the pump seems to run all the time, the check valve is a prime suspect.
Electrical and power problems
Pentair’s troubleshooting FAQ says the most common cause of sump pump failure is electrical. Plugging the pump into an extension cord, or into an outlet that shares a circuit with other devices, causes low voltage and a higher amp draw, and the motor overheats. Then there’s the power outage itself. In a storm, the grid and the pump fail at the same moment, which is why a battery backup matters.
Clogged intake or worn motor
Silt, gravel and debris can jam the impeller or block the intake screen. A pump that sits directly on the pit floor draws in more of this material. The ICLR booklet suggests raising the pump a few centimeters off the bottom of the basin, and notes that PVC grates sold for this purpose are available at home improvement stores. An old motor that overheats, trips breakers or vibrates heavily is usually near the end of its life.
A clogged or damaged discharge line
If the pump runs but the pit doesn’t drop, water may not be leaving. A crushed, frozen or clogged discharge line, or one that drains right back toward the house, makes the pump work without moving water out. This is plumbing work, not pump work, and it’s one reason a new pump alone sometimes doesn’t fix the problem.

What you can safely check first
Water and electricity are a dangerous mix, so keep the checks short and dry-handed.
- Confirm there’s power. Look at the breaker and the GFCI outlet. Reset a tripped GFCI once. If it trips again, stop.
- Look for a pulled or loose plug. Make sure the pump is not on an extension cord.
- Test the float. Pentair says to lift the float with a broom handle or another non-conducting item so you avoid shock, and not to leave the pump plugged in for more than a few minutes so it doesn’t overheat.
- Check the pit for debris. Look, don’t reach in with the pump plugged in.
- Note what you hear and see. Humming, grinding, a burning smell, a tripped breaker: tell the plumber exactly what happened.
Stop if the electrical panel is in a flooded area or you aren’t sure the area is safe. State Farm advises that water-damaged electrical equipment should be inspected before use and that a licensed electrician or the electric utility should be called in those conditions rather than attempting DIY repair.
A pump that turns on when you lift the float isn’t proof that it’s protecting the property. It doesn’t tell you whether the check valve holds, whether the discharge line is clear or whether the pump will run on backup power. That is where a professional visit earns its fee.
When to call a plumber
Call right away if any of these apply. Sump Alarm’s guidance lists a licensed plumber, pump technician or electrician as the right contact when:
- water or sewage is backing up, or water is close to overflowing;
- the pump won’t run after you’ve confirmed power;
- the pump hums but doesn’t pump;
- the breaker trips repeatedly;
- the alarm keeps coming back;
- the system involves sewage, septic, a grinder pump or a lift station.
Add to that list a burning smell, water leaking from the motor housing, or a pit that keeps filling in dry weather. That last one can point to a broken pipe or a drainage problem rather than a pump problem. If a pipe is involved, our guides to burst pipe repair and slab leak detection and repair explain what that looks like. If sewage is coming up anywhere, read what to do about a sewage backup and call right away.
For homeowners, landlords and property managers alike, the rule is simple: if water is on the floor or the pump is silent during a storm, don’t wait for a better time.
What a sump pump repair visit covers
A thorough visit follows the water path from the pit to the point where it leaves your property. Expect a plumber to:
- Inspect the pit. Clear silt and debris, check the pump’s position and make sure the intake is free.
- Test the float. Raise the water level or lift the float to confirm the pump starts and stops at the right points, and that nothing snags.
- Check the electrical supply. Verify the outlet, the circuit and the plug are correct and that the pump isn’t running on an extension cord.
- Examine the check valve. Confirm it holds water in the discharge pipe instead of letting it drain back.
- Trace the discharge line. Look for clogs, cracks, kinks and a termination point that sends water away from the structure.
- Test the alarm and backup. If you have a battery backup or high-water alarm, confirm it works.
- Run the pump through a full cycle. The goal is to see it start, pump down and shut off cleanly.
Then comes the decision: repair the part, or replace the unit. A plumber should explain which and why, and give you the price before the work begins. Our approach is transparent pricing and clear warranties on labor and manufacturer parts.
Repair or replace?
Repair makes sense when the failed part is small and the pump is otherwise sound: a float switch, a check valve, a section of discharge pipe, a bad outlet. Replace when:
- the motor has failed or the housing leaks;
- the impeller is seized and can’t be freed by hand;
- the pump is about 10 years old and has been working hard;
- repairs have started to repeat.
A sealed submersible motor isn’t a home project. Water System Wiki explains that opening and fixing it will almost certainly destroy it and void the warranty, so a failed motor means a new pump.
The City of Ann Arbor guide mentions one practical idea: when you install a new pump, the older pump with a new switch can stay as an emergency backup, since switches are relatively inexpensive to replace. Ask your plumber whether that suits your pit size.
As for lifespan, Westfield Insurance puts the average at about 10 years with proper maintenance, and sooner if the pump works hard. A pump that runs constantly because the water table is high will age faster than one that runs a few times a year.
What sump pump repair costs
Prices vary by pump type, access, parts and the time of day you call. For national context, Forbes Home reports an average repair cost of $475, with low-end jobs averaging $400 and high-end jobs $550. Pedestal pumps run $400 to $475 to repair and submersible pumps $475 to $550.
| Factor | How it affects the price |
|---|---|
| Pump type | Pedestal repairs average less than submersible repairs |
| Failed part | A float switch or check valve is cheaper than a discharge line repair |
| Repair vs. replacement | Replacement adds the pump itself plus installation |
| Backup system | Adding a battery backup or alarm adds equipment cost |
| Timing | Emergency and after-hours calls cost more than scheduled visits |
These are national averages, not our quotes. We don’t publish a flat price for sump pump work, since the right fix depends on what the plumber finds. What we do commit to is a clear price before work starts. For context on how we publish other prices, a drain or blockage clearing job is $99, and water heater installation and repairs start from $1,450.
One thing worth weighing: a flooded finished space can cost far more to dry out, clean and restore than any pump repair. Fixing a failing pump before the storm is nearly always the cheaper path.
Our view: repair the system, not just the pump
We get called to sump pump jobs where a new pump was installed and the problem came back. Usually the pump was never the whole story. The discharge line was crushed, the check valve was missing, the outlet was overloaded or the pit was filling for a reason nobody had traced.
That’s why we look at the whole water path: pit, pump, valve, power, discharge and where the water ends up. A plumber who also handles drains, leaks and sewer lines can see the difference between a pump problem and a pipe problem on the first visit, instead of sending you to someone else when the first fix doesn’t hold.
We work 24/7 because water doesn’t wait for business hours, and we aim to complete most jobs within 24 hours. We price transparently and back our work with warranties on labor and manufacturer parts. If a repair is enough, we’ll say so. If the pump has reached the end of its life, we’ll show you why and replace it properly.
Shawn
How to keep your sump pump from failing
Most failures give a warning first. A short routine catches them.
- Test twice a year, and again before the heavy rains start. Pour water into the pit until the float rises, and watch the pump start, empty the pit and shut off.
- Clean the pit and intake of silt, gravel and debris.
- Give the pump its own outlet. No extension cords, no shared circuits with other devices.
- Confirm the check valve and discharge line. Water should leave the property, not pool next to it.
- Add a battery backup and an alarm. Westfield notes that a backup lets the pump keep running when power is out, and an alarm warns you when the water level is too high or the power goes out. The batteries need to be replaced every few years.
- Keep a record of the date and what you did, in case a landlord, tenant or insurer asks.
Hurricane season is the most predictable stress test on the Gulf Coast. Before storms arrive, move valuables off low floors and out of crawl spaces. Our partner-neutral advice on preparing belongings for hurricane season is a good companion to a pump check: one protects the water path, the other protects what’s in its way.
Need a plumber for your sump pump?
If your pump is failing, noisy or silent, we’ll find out which, fix what needs fixing and tell you the price first. We serve homeowners, landlords, property managers and businesses across St. Petersburg, Clearwater, Largo, Seminole, Oldsmar and nearby cities, around the clock.

See our plumbing services, or contact us through the IronLadd Plumbing homepage. If you’re in Pinellas County, our St. Petersburg and Clearwater pages show how we cover your area.
FAQ
Why is my sump pump running constantly?
The most likely causes are a float switch stuck in the ON position, a failed check valve letting water drain back into the pit, or a pit that is filling constantly from high groundwater. A constantly running pump wears out faster, so have it checked soon.
Can I fix a sump pump myself?
You can safely check the power and the float, and clear visible debris with the pump unplugged. Electrical faults, a damaged discharge line and a failed motor are plumber jobs, and a sealed motor can’t be repaired at home.
How long does a sump pump last?
About 10 years with proper maintenance, according to Westfield Insurance. A pump that runs often, or in a high water table, may need replacing sooner.
How much does sump pump repair cost?
Forbes Home reports a national average of $475, ranging from about $400 to $550. The final price depends on the pump type, the failed part and the time of the call.
Does a sump pump work during a power outage?
Not unless it has a battery backup or another backup power source. Storms often cut power at the same time as they raise water levels, so a backup and an alarm are worth discussing with your plumber.
Sources
- Common Points of Failure (City of Ann Arbor)
- Sump Pump Troubleshooting FAQ (Pentair)
- Sump pump systems (ICLR)
- How Often Should You Test Your Sump Pump? (Southern Living)
- Why Is My Sump, Septic, or Sewage Alarm Going Off? (Sump Alarm)
- What To Do When Your Basement Floods (State Farm)
- Sump Pump Repair vs. New Installation (Water System Wiki)
- How Much Does Sump Pump Repair Cost (Forbes Home)
- Sump Pump Failure Insurance: What to Know (Westfield)
- How to Prepare Your Belongings for Hurricane Season in Hudson, Florida
Recommended
Need a plumber today?
Call or Text (727) 365-7882